Sunday, October 18, 2020

Pandmic Projects 4: Terrain Making and Casting

 I've had a few terrain projects dangling near-finished for a while, but I lacked the motivation to get the over the finish line.  some like gun position has been sitting around needing to be grassed for 9 months. others like the walls have only been sitting idle for 2 or 3 months. then there is the bridge, which I bought at HotLead(I think?) in Ontario 6 years ago, before i moved to Edmonton.either way i decided i needed to get some  finished.


The bridge was a great find.  I bought it at the HotLead fleamarket 6 or 7 years ago, broken in two.  I knew I could pin it and fix it, and more importantly, it fits 50x50mm bases perfectly! it also happens to fit my river system well.  it also painted up really nice.

It had broken right at the middle point to the side of the central arch stone. I pined it in 4 places for extra strength.

Side shot of bridge
 

50x50mm bases fit perfectly!

 Next is gun position. I built this a year ago as a test bed for some techniques in making wood texture. it was a general success. I used Renedra wattle fencing and gabions, but I intent to make my own for future projects.  in the future I'll probably also make the walls higher. they came out a little lower then I'd want.

The texture on hte wood planks was created by "scrubbing" the wood with a wire brush. The wood used was basswood.

Position occupied by Napoleonic British guns

Lower angle to show the height of the position walls.

Reverse angle. Note the texture on the planks.

 

This wall project started both because I wanted some more walls, but also because I wanted to try my hand at casting in 2-part self-skinning polyurethane expanding foam.  i started by making some dry stone walls. I had to modify how i cast them, but they ended up working ok.  there are some bubbles because I don't have a vacuum chamber I can't really do much about it. Note on the drystone walls the moss/vines on the walls furthest from the camera. I did that to cover up places where walls were damaged coming out of the mold the first few times. the skin would separate from the foam. I managed to solve the issue after a few castings.  Each wall section is 6 inches long. for this set, i have a single straight wall, one with a gate, and one with a corner on the end like the old GW stone walls.


the 3 unique lengths of wall.

A three sided paddock defended by the Buffs

From a lower angle so you can see the height

 

The second set of walls is more of an attempt to replace my old GW fantasy stone walls. you can't get them anymore, and they are slowly breaking.  I built these out of individual styrofoam blocks textured with a foil ball. the blocks are on average under half the size of the massive 200lb blocks the GW ones are apparently made out of. I also varied the block size a bit more. So there are some that are very small and some that are almost the size of the GW ones, near the bottom usually.  I built two unique straight sections, one section with a corner, and one with a gateway/opening. I've seen these style of opening in several pictures of similar style old stone walls.

These cast nicer then the dry stone walls. I thin there are less extreme changes in topograghy for air to get stuck in. there are still air bubbles but they are generally less noticeable.

the four unique sections of wall

Three of the master walls shown with a GW
Fantasy stone wall for comparison

From a lower angle so you can see the height


And finally, a well I bought on Friday this well is from the Wizkids "Deep Cuts" line of scatter terrain and accessories.  They are cheap ($6.95 CDN, or about $5 USD) and are full of detail. This one came with a little water insert that pops out easily.  good 28mm wells aren't easy to find so I'm glad I got this one for really cheap.


Deep Cuts well with water insert out

Well with water insert in



As some of you might have noticed, I'm trying to update once every week or two now. we'll see how long that lasts.  being unemployed certainly makes finding the time a bit easier.  Its also nice to have some Motivation to paint. The lack of historical gamers in Edmonton combined with lack of gaming during the pandemic had certainly taken its toll.

Cheers!

2 comments:

  1. Nice work all around. Your gun emplacement is my favorite.

    ReplyDelete
  2. Excellent effort on the the walls and small redoubt. Also, thanks for the info on the awesome crafted well. I must get a couple myself. I am enjoying your posts, thanks.
    Rod

    ReplyDelete